NJDEP Large Scale Wind Turbine Siting Map

Metadata also available as

Metadata:

Identification_Information:
Citation:
Citation_Information:
Originator:
New Jersey Department of Environmental Protection (NJDEP), Division of Fish and Wildlife (DFW), Endangered and Nongame Species Program (ENSP)
Publication_Date: 200909
Title: NJDEP Large Scale Wind Turbine Siting Map
Edition: Version 1.0, 20090808
Geospatial_Data_Presentation_Form: vector digital data
Publication_Information:
Publication_Place: Trenton, NJ
Publisher: NJ Department of Environmental Protection (NJDEP)
Other_Citation_Details:
ADVISORY: This layer depicts land areas in the coastal zone where large scale wind turbines are unacceptable due to the operational impacts of turbines on birds and bats.
Downloadable files available thru Online Linkage.
Online_Linkage:
<http://www.state.nj.us/dep/gis/digidownload/zips/statewide/windturbinesiting.zip>
Description:
Abstract:
ADVISORY: This layer depicts land areas in the coastal zone where large scale wind turbines are unacceptable due to the operational impacts of turbines on birds and bats.
On September 7, 2010, the Department adopted amendments to the Coastal Permit Program rules, N.J.A.C. 7:7 and Coastal Zone Management rules, N.J.A.C. 7:7E to address the development and permitting of wind turbines in the coastal zone. As the height and size of wind turbines increase, so does the potential for adverse impacts to both birds and bats due to the operation of the turbines. The Department has evaluated the land in the coastal zone and prepared the Large Scale Wind Turbine Siting Map which identifies specific areas where wind turbines 200 feet in height or taller or having a cumulative rotor swept area of greater than 4,000 square feet are unacceptable due to the operational impacts of the turbines on birds and bats. In order to minimize adverse effects on birds and bats, N.J.A.C. 7:7-7.31 and 7:7E-7.4(r) require wind energy facilities located on land to be sited such that no portion of the wind turbine(s), including blades, towers and site disturbance will be located in areas identified on the Department's Large Scale Wind Turbine Siting Map. The map was created by combining the NJDEP aerial photo-based LU/LC data layer with wildlife locations within the coastal zone where there are high concentrations of resident and migratory songbirds, raptors, and shorebirds that are considered to be "at risk" of colliding with wind turbines.
Purpose:
The Large Scale Wind Turbine Siting Map identifies areas on land where wind turbines 200 feet in height or taller or having a cumulative rotor swept area of greater than 4,000 square feet are unacceptable due to the operational impacts of the turbines on birds and bats (See N.J.A.C. 7:7-7.31 and 7:7E-7.4(r)).
Supplemental_Information:
A cross reference of the NJDEP 2002 Land Use/Land Cover is essential because version 1.0 of the Large Scale Wind Turbine Siting Map relies on the accuracy and methodology of that data. Citation reference information can be found in the Cross Reference section of this metadata document. The abstract for the NJDEP 2002 Land use/Land cover Update is below:
The 2002 LU/LC was created by comparing the 1995/97 LU/LC layer from NJ DEP's geographical information systems (GIS) database to 2002 color infrared (CIR) imagery and delineating areas of change. Work for this data set was done by Aerial Information Systems, Inc., Redlands, CA, under direction of the New Jersey Department of Environmental Protection (NJDEP), Bureau of Geographic Information System (BGIS). LU/LC changes were captured by adding new line work and attribute data for the 2002 land use directly to the base data layer. All 1986 LU/LC polygons and attribute fields were removed from this update, however, all 1995/97 LU/LC polygons remain in this data set, so change analysis can be undertaken from this one layer. The classification system used was a modified Anderson et al., 2002 classification system. An impervious surface (IS) code was also assigned to each LU/LC polygon based on the percentage of impervious surface within each polygon as of 2002 and 1995/97. Minimum mapping unit (MMU) is 1 acre.
Time_Period_of_Content:
Time_Period_Information:
Single_Date/Time:
Calendar_Date: 2009
Currentness_Reference: publication date
Status:
Progress: Complete
Maintenance_and_Update_Frequency: Unknown
Spatial_Domain:
Bounding_Coordinates:
West_Bounding_Coordinate: -75.551318
East_Bounding_Coordinate: -73.902378
North_Bounding_Coordinate: 41.006513
South_Bounding_Coordinate: 38.924835
Keywords:
Theme:
Theme_Keyword_Thesaurus: None
Theme_Keyword: biodiversity
Theme_Keyword: protected areas
Theme_Keyword: birds
Theme_Keyword: endangered species
Theme_Keyword: nature conservation
Theme_Keyword: protected species
Theme_Keyword: rare species
Theme_Keyword: terrestrial ecosystems
Theme_Keyword: wetlands
Theme_Keyword: wildlife
Theme_Keyword: wind energy
Theme_Keyword: wind turbines
Theme_Keyword: zoology
Theme:
Theme_Keyword_Thesaurus: ISO 19115 Topic Category
Theme_Keyword: biota
Place:
Place_Keyword_Thesaurus: None
Place_Keyword: New Jersey
Place_Keyword: NJ
Temporal:
Temporal_Keyword_Thesaurus: None
Temporal_Keyword: 2009
Access_Constraints: none
Use_Constraints:
NJDEP/DFW/ENSP Data Use Disclaimer for Large Scale Wind Turbine Siting Map.
This layer depicts land areas in the coastal zone where large scale wind turbines are unacceptable due to the operational impacts of turbines on birds and bats.
New Jersey Department of Environmental Protection (NJDEP)
Data Distribution Agreement
I. Description of Data to be Provided.
The data provided herein are distributed subject to the following conditions and restrictions:
SUBJECT DATA LAYERS
For all data contained herein, NJDEP makes no representations of any kind, including, but not limited to, the warranties of merchantability or fitness for a particular use, nor are any such warranties to be implied with respect to the digital data layers furnished hereunder. NJDEP assumes no responsibility to maintain them in any manner or form.
II.Terms of Agreement
1. Digital data received from the NJDEP are to be used solely for internal purposes in the conduct of daily affairs.
2. The data are provided, as is, without warranty of any kind and the user is responsible for understanding the accuracy limitations of all digital data layers provided herein, as documented in the accompanying cross-reference files (see SUPPLEMENTAL INFORMATION). Any reproduction or manipulation of the above data must ensure that the coordinate reference system remains intact.
3. Digital data received from the NJDEP may not be reproduced or redistributed for use by anyone without first obtaining written permission from the NJDEP. This clause is not intended to restrict distribution of printed mapped information produced from the digital data.
4. Any maps, publications, reports, or other documents produced as a result of this project that utilize NJDEP digital data will credit the NJDEP's Geographic Information System (GIS) as the source of the data with the following credit/disclaimer:
"This (map/publication/report) was developed using New Jersey Department of Environmental Protection Geographic Information System digital data, but this secondary product has not been verified by NJDEP and is not state-authorized."
5. Users shall require any independent contractor, hired to undertake work that will utilize digital data obtained from the NJDEP, to agree not to use, reproduce, or redistribute NJDEP GIS data for any purpose other than the specified contractual work. All copies of NJDEP GIS data utilized by an independent contractor will be required to be returned to the original user at the close of such contractual work.
Users hereby agree to abide by the use and reproduction conditions specified above and agree to hold any independent contractor to the same terms. By using data provided herein, the user acknowledges that terms and conditions have been read and that the user is bound by these criteria.
Point_of_Contact:
Contact_Information:
Contact_Person_Primary:
Contact_Person: Patrick Woerner
Contact_Organization: NJDEP/DFW/ENSP
Contact_Position: GIS Specialist
Contact_Address:
Address_Type: mailing and physical address
Address: 501 East State Street, PO Box 400
City: Trenton
State_or_Province: NJ
Postal_Code: 08625
Country: USA
Contact_Voice_Telephone: 609-292-9400
Contact_Facsimile_Telephone: 609-984-1414
Contact_Electronic_Mail_Address: Patrick.Woerner@dep.state.nj.us
Hours_of_Service: 9-5
Browse_Graphic:
Browse_Graphic_File_Name:
<http://www.state.nj.us/dep/gis/digidownload/images/statewide/windturbinesiting.gif>
Browse_Graphic_File_Description: image
Browse_Graphic_File_Type: GIF
Data_Set_Credit:
NJ Department of Environmental Protection (NJDEP), Office of Information Resources Management (OIRM), Bureau of Geographic Information System (BGIS)
Native_Data_Set_Environment:
Microsoft Windows XP Version 5.1 (Build 2600) Service Pack 3; ESRI ArcCatalog 9.2.6.1500
Cross_Reference:
Citation_Information:
Originator:
NJDEP, Division of Fish and Wildlife, Endangered and Nongame Species Program
Publication_Date: 2009
Title: Large Scale Wind Turbine Siting Map Report
Edition: Version 1.0
Geospatial_Data_Presentation_Form: map
Publication_Information:
Publication_Place: Trenton, NJ
Publisher: NJDEP
Online_Linkage: <http://www.nj.gov/dep/landuse/forms/index.html#coastal>
Data_Quality_Information:
Attribute_Accuracy:
Attribute_Accuracy_Report:
Checked for invalid attribute codes and corrected as identified.
Logical_Consistency_Report:
Topological accuracy is dependent upon the NJDEP 2002 Land Use/Land cover. See the Cross Reference section of this metadata document for further information on the 2002 Land Use/Land cover. Further tests were done to correct unclosed polygons after this data was dissolved.
Completeness_Report: The data layer is complete. No omissions
Positional_Accuracy:
Horizontal_Positional_Accuracy:
Horizontal_Positional_Accuracy_Report: Based on NJDEP Land Use/Land Cover. NMAS at 1:12000
Vertical_Positional_Accuracy:
Vertical_Positional_Accuracy_Report: NA
Lineage:
Source_Information:
Source_Citation:
Citation_Information:
Originator:
NJ Department of Environmental Protection (NJDEP), Office of Information Resources Management (OIRM), Bureau of Geographic Information Systems (BGIS)
Publication_Date: 20060502
Title: NJDEP 2002 Land use/Land cover Update for New Jersey (by WMA)
Edition: FINAL
Geospatial_Data_Presentation_Form: vector digital data
Publication_Information:
Publication_Place: Trenton, NJ
Publisher: NJDEP
Online_Linkage: <http://www.state.nj.us/dep/gis/lulc02shp.html>
Source_Scale_Denominator: 12000
Type_of_Source_Media: vector digital data
Source_Time_Period_of_Content:
Time_Period_Information:
Single_Date/Time:
Calendar_Date: 2002
Source_Currentness_Reference: ground condition
Source_Citation_Abbreviation: 2002 LULC
Source_Contribution:
A cross reference of the NJDEP 2002 Land Use/Land Cover is essential because the Large Scale Wind Turbine Siting Map relies on the accuracy and methodology of that data. Citation reference information can be found in the Cross Reference section of this metadata document. The abstract for the NJDEP 2002 Land use/Land cover Update is below:
The 2002 LU/LC was created by comparing the 1995/97 LU/LC layer from NJ DEP's geographical information systems (GIS) database to 2002 color infrared (CIR) imagery and delineating areas of change. Work for this data set was done by Aerial Information Systems, Inc., Redlands, CA, under direction of the New Jersey Department of Environmental Protection (NJDEP), Bureau of Geographic Information System (BGIS). LU/LC changes were captured by adding new line work and attribute data for the 2002 land use directly to the base data layer. All 1986 LU/LC polygons and attribute fields were removed from this update, however, all 1995/97 LU/LC polygons remain in this data set, so change analysis can be undertaken from this one layer. The classification system used was a modified Anderson et al., 2002 classification system. An impervious surface (IS) code was also assigned to each LU/LC polygon based on the percentage of impervious surface within each polygon as of 2002 and 1995/97. Minimum mapping unit (MMU) is 1 acre.
Source_Information:
Source_Citation:
Citation_Information:
Originator: NatureServe
Publication_Date: 2009
Title: Biotics Database
Publication_Information:
Publication_Place: Arlington, VA
Publisher: NatureServe
Source_Scale_Denominator: 12000
Type_of_Source_Media: table
Source_Time_Period_of_Content:
Time_Period_Information:
Single_Date/Time:
Calendar_Date: 20090406
Source_Currentness_Reference: publication date
Source_Citation_Abbreviation: Biotics database
Source_Contribution:
Source observation features (points, lines, polygons) were exported from the Biotics database. For more information regarding NatureServe's Element Occurrence Data Standard, please refer to <http://www.natureserve.org/prodServices/eodata.jsp>.
Process_Step:
Process_Description:
The general method for delineating the "Large Scale Wind Turbine Siting Map" includes both species and regional approaches that are detailed below.
SPECIES MAPPING:
The Department considers certain species to be at risk of colliding with wind turbines due to their flight behavior, life history characteristics, and/or because collision events have been documented. To avoid unintentional impacts to these species as a result of wind-power development, habitats known to be important for the species listed below have been included in the Large Scale Wind Turbine Siting Map and are therefore off limits to large scale wind development.
Species source feature data for bald eagle, black skimmer, least tern, black-crowned night-heron, yellow-crowned night heron, piping plover, red knot and migratory shorebird concentration sites were exported from the Biotics database as three separate shapefiles (points, lines, and polygons). Species-specific buffers were applied to these source feature data and were used to clip the NJDEP 2002 Land-use/Land-cover (LU/LC). Using the 2002 LU/LC TYPE02 codes and LU02 codes as a guide, clipped areas were evaluated and LU/LC polygons were selected to represent habitat most likely to be utilized by the species. All clipped LU/LC polygons were dissolved with other species and regional (see REGIONAL MAPPING below) data to form contiguous areas off-limits to large scale wind turbine development. Where mapped areas contained more than 50% of a marsh island, the LU/LC polygons that represent the marsh islands were selected and dissolved into the layer. Lastly, all polygons less than one acre were evaluated and those that were both separated from the species source feature by water and on the periphery of a species buffer, were deleted because they did not protect a significant portion of habitat for the species. For a detailed description of the mapping methodology, consult the "Large Scale Wind Turbine Siting Map Report" available at: <http://www.nj.gov/dep/landuse/forms/index.html#coastal>
REGIONAL MAPPING:
The Department considers the regions listed below to represent areas within the New Jersey coastal zone where birds are known to concentrate or where rare species nest. The species considered in the delineation of these regions were those documented to be at risk of colliding with wind turbines and/or species that exhibit flight patterns or behaviors that put them in collision risk. To avoid unintentional impacts to these species as a result of wind-power development, these regions have been included in the Large Scale Wind Turbine Siting Map and are therefore off limits to large scale wind development.
1) Hereford Inlet and the back-bay areas west of Stone Harbor: A polygon was hand-digitized to capture all known osprey nests in the back bays and marshes west of Stone Harbor and Avalon. This polygon was used to select appropriate NJDEP 2002 LU/LC polygons, which were then combined/dissolved to create the region.
2) Little Egg, Brigantine Inlets, and Mullica River Region: NJDEP 2002 LU/LC polygons were selected to approximate the boundaries of federally-owned Holgate and Little Beach (part of Forsythe National Wildlife Refuge), and state-owned North Brigantine Natural Area and Great Bay Boulevard Wildlife Management Area. A small number of the northeastern-most islands of the Absecon Wildlife Management Area were also included. In addition, polygons were hand-digitized to capture all known osprey nests, bald eagle foraging and wintering areas, northern harrier nests, and peregrine falcon nests in this region. These polygons were used to select appropriate NJDEP 2002 LU/LC polygons. All selected NJDEP 2002 LU/LC polygons were combined/dissolved to create the region.
3) Sedge Island and Island Beach State Park: NJDEP 2002 LU/LC polygons were selected to approximate Island Beach State Park and most of the Sedge Island Wildlife Management Area (WMA). Where necessary, additional LU/LC polygons were selected to capture all known osprey nests in the Sedge Island WMA and the southern shore of Island Beach State Park. All selected NJDEP 2002 LU/LC polygons were combined/dissolved to create the region.
4) Gateway National Recreation Area - Sandy Hook Unit: NJDEP 2002 LU/LC polygons were selected to approximate the boundaries of the Sandy Hook Unit of the Gateway National Recreation Area. Where necessary, additional LU/LC polygons were selected to capture all known osprey nests on the Sandy Hook Unit. All selected NJDEP 2002 LU/LC polygons were combined/dissolved to create the region.
5) Stow Creek and Mannington Meadows: Polygons were hand-digitized to capture all known bald eagle nesting, foraging and wintering areas. These polygons were used to select appropriate NJDEP 2002 LU/LC polygons, including those that linked nest locations with the most proximate open water foraging areas. All selected NJDEP 2002 LU/LC polygons were combined/dissolved to create these regions.
6) Great Egg Harbor: Polygons were hand-digitized to capture all known osprey nests, bald eagle foraging and wintering areas, northern harrier nests, and peregrine falcon nests on the lower Tuckahoe, Middle and Great Egg Harbor rivers. These polygons were used to select appropriate NJDEP 2002 LU/LC polygons which were then combined/dissolved to create the region.
7) Palisades: A polygon was hand-digitized to capture all known peregrine falcon nests that occur on the Palisades Interstate Park cliffs. This polygon was used to select appropriate NJDEP 2002 LU/LC polygons, which were then combined/dissolved to create the region.
8) Cape May Peninsula and Delaware Bay Shore: This region encompasses the most southerly 20 kilometers of the Cape May Peninsula ("the lower 20K") and the habitats along the Delaware Bayshore. The mapped areas described below were combined and dissolved to create the region. The lower 20K extends from the southern tip of the peninsula to an area roughly three kilometers north of Cape May Court House. All NJDEP 2002 LU/LC polygons within this area were selected, with the exception of LU/LC polygons with TYPE02 coded as "WATER." Those LU/LC polygons that extended beyond the northern boundary line of the lower 20K, were clipped by the boundary. All selected NJDEP 2002 LU/LC polygons were dissolved into contiguous areas. The mapped portion of the Delaware Bayshore extends from the northern boundary of the lower 20K, northwest along the bayshore, to approximately five kilometers beyond the Cohansey River, and inland from the shoreline of the bay to the CAFRA boundary. Within this area, the following coastal wetlands (LU02: 6100) were selected from the NJDEP 2002 LU/LC: "SALINE MARSH (LOW MARSH)" (LU02: 6111), "SALINE MARSH (HIGH MARSH)" (LU02: 6112), "FRESHWATER TIDAL MARSHES" (LU02: 6120), "VEGETATED DUNE COMMUNITIES" (LU02: 6130), and "PHRAGMITES DOMINATE COASTAL WETLANDS" (LU02: 6141). These coastal wetlands were buffered by one kilometer and dissolved into contiguous areas. Areas outside of a wetland buffer, that were both completely surrounded by the buffered area and less than 50 acres in size, were identified and dissolved into the surrounding buffered area. All NJDEP 2002 LU/LC polygons within a buffered area were selected, with the exception of LU/LC polygons with TYPE02 coded as "WATER". Those LU/LC polygons that extended beyond the boundary of the buffered areas, were clipped by the boundary. Where necessary, additional LU/LC polygons were selected to capture all known bald eagle nests in this region. All selected NJDEP 2002 LU/LC polygons were dissolved into contiguous areas.
Process_Date: 200908
Cloud_Cover: 0
Spatial_Data_Organization_Information:
Direct_Spatial_Reference_Method: Vector
Point_and_Vector_Object_Information:
SDTS_Terms_Description:
SDTS_Point_and_Vector_Object_Type: G-polygon
Point_and_Vector_Object_Count: 1170
Spatial_Reference_Information:
Horizontal_Coordinate_System_Definition:
Planar:
Map_Projection:
Map_Projection_Name: Transverse Mercator
Transverse_Mercator:
Scale_Factor_at_Central_Meridian: 0.999900
Longitude_of_Central_Meridian: -74.500000
Latitude_of_Projection_Origin: 38.833333
False_Easting: 492125.000000
False_Northing: 0.000000
Planar_Coordinate_Information:
Planar_Coordinate_Encoding_Method: coordinate pair
Coordinate_Representation:
Abscissa_Resolution: 0.061
Ordinate_Resolution: 0.061
Planar_Distance_Units: survey feet
Geodetic_Model:
Horizontal_Datum_Name: North American Datum of 1983
Ellipsoid_Name: Geodetic Reference System 80
Semi-major_Axis: 6378137.000000
Denominator_of_Flattening_Ratio: 298.257222
Vertical_Coordinate_System_Definition:
Altitude_System_Definition:
Altitude_Datum_Name: North American Vertical Datum of 1988
Altitude_Resolution: 0.000100
Altitude_Distance_Units: feet
Altitude_Encoding_Method:
Explicit elevation coordinate included with horizontal coordinates
Entity_and_Attribute_Information:
Detailed_Description:
Entity_Type:
Entity_Type_Label: windturbinesiting
Entity_Type_Definition: Attributes for Large Scale Wind Turbine Siting Map
Entity_Type_Definition_Source: NJDEP
Attribute:
Attribute_Label: FID
Attribute_Definition: Internal feature number.
Attribute_Definition_Source: ESRI
Attribute_Domain_Values:
Unrepresentable_Domain:
Sequential unique whole numbers that are automatically generated.
Attribute:
Attribute_Label: Shape
Attribute_Definition: Feature geometry.
Attribute_Definition_Source: ESRI
Attribute_Domain_Values:
Unrepresentable_Domain: Coordinates defining the features.
Attribute:
Attribute_Label: ID
Attribute_Definition:
Unique identifier for each contiguous polygon off-limits to large scale wind development
Attribute_Definition_Source: NJ Division of Fish and Wildlife
Attribute_Domain_Values:
Unrepresentable_Domain: Unique Entry
Attribute:
Attribute_Label: LABEL
Attribute_Definition:
Label for each contiguous area off limits to large scale wind development
Attribute_Definition_Source: NJ Division of Fish and Wildlife
Attribute_Domain_Values:
Unrepresentable_Domain: Unique Entry
Attribute:
Attribute_Label: VERSION
Attribute_Definition: Number used to track version
Attribute_Definition_Source: NJ Division of Fish and Wildlife
Attribute_Domain_Values:
Unrepresentable_Domain: Unique Entry
Attribute:
Attribute_Label: Acres
Attribute_Definition: Acres of polygon
Attribute_Definition_Source: Calculated by XTools Pro extension to ArcGIS
Attribute_Domain_Values:
Unrepresentable_Domain: Unique Entry
Attribute:
Attribute_Label: Hectares
Attribute_Definition: Hectares of polygon
Attribute_Definition_Source: Calculated by XTools Pro extension to ArcGIS
Attribute_Domain_Values:
Unrepresentable_Domain: Unique Entry
Overview_Description:
Entity_and_Attribute_Overview:
The attributes in this data set describe land use/land cover categories for each polygon from 1995/97 and 2002. The classification system used is a modified Anderson classification system. In addition, some attributes are included for non-tidal wetlands that use the Cowardin classification system. Percent impervious surface for each polygon is also given.
Entity_and_Attribute_Detail_Citation: none
Distribution_Information:
Distributor:
Contact_Information:
Contact_Organization_Primary:
Contact_Organization: NJDEP/DFW/ENSP
Contact_Person: Patrick Woerner
Contact_Address:
Address_Type: mailing and physical address
Address: 501 East State Street, PO Box 400
City: Trenton
State_or_Province: NJ
Postal_Code: 08625
Country: USA
Contact_Voice_Telephone: 609-292-1244
Contact_Facsimile_Telephone: 609-984-1414
Contact_Electronic_Mail_Address: Patrick.Woerner@dep.state.nj.us
Resource_Description: Downloadable Data
Distribution_Liability:
This organization provides the geographic data "as is". This organization makes no guarantee or warranty concerning the accuracy of information contained in the geographic data. Also, this organization makes no warranty either expressed or implied, regarding the condition of the product or its fitness for any particular purpose. The burden for determining fitness for use lies entirely with the user. Although these files have been processed successfully on computers at this organization, no warranty is made by this organization regarding the use of these data on any other system, nor does the fact of distribution constitute or imply any such warranty.
Standard_Order_Process:
Digital_Form:
Digital_Transfer_Information:
Format_Name: AVSHP
Format_Version_Number: 9x
File_Decompression_Technique: Winzip
Transfer_Size: 12.2
Digital_Transfer_Option:
Online_Option:
Computer_Contact_Information:
Network_Address:
Network_Resource_Name: <http://www.state.nj.us/dep/gis/stateshp.html>
Offline_Option:
Offline_Media: none
Recording_Format: none
Fees: none
Ordering_Instructions: none
Available_Time_Period:
Time_Period_Information:
Single_Date/Time:
Calendar_Date: 2009
Metadata_Reference_Information:
Metadata_Date: 20090807
Metadata_Contact:
Contact_Information:
Contact_Person_Primary:
Contact_Person: Patrick Woerner
Contact_Organization:
NJDEP, Division of Fish and Wildlife, Endangered and Nongame Species Program
Contact_Position: GIS Specialist
Contact_Address:
Address_Type: mailing and physical address
Address: 501 East State Street, PO Box 400
City: Trenton
State_or_Province: New Jersey
Postal_Code: 08625
Country: USA
Contact_Voice_Telephone: 609-292-1244
Contact_Facsimile_Telephone: 609-984-1414
Contact_Electronic_Mail_Address: Patrick.Woerner@dep.state.nj.us
Hours_of_Service: 9-5
Metadata_Standard_Name: FGDC Content Standards for Digital Geospatial Metadata
Metadata_Standard_Version: FGDC-STD-001-1998
Metadata_Time_Convention: local time
Metadata_Extensions:
Online_Linkage: <http://www.esri.com/metadata/esriprof80.html>
Profile_Name: ESRI Metadata Profile
Generated by mp version 2.9.6 on Wed Sep 22 15:27:49 2010