Site Remediation Waste Management Program Community Corner
Welcome to Community Corner's "What's in My Community" rollout of the Immediate Environmental Concern (IEC) GIS Layer. The purpose of the IEC GIS layer is to identify all
IEC locations with response actions performed or overseen by the Division of Remediation Management, Site Remediation and Waste Management Program (SRWMP) at the New Jersey
Department of Environmental Protection (NJDEP). An IEC is the highest priority case in the SRWMP. The IEC GIS layer can be viewed in the
Site Remediation Profile in NJ-Geoweb.
The IEC GIS layer itself is located under the "Sites and Facilities" grouping.
What Is An IEC?
An IEC is a condition that involves actual human exposure to hazardous substances that exceed applicable health-based criteria, screening levels, or standards resulting from
the release of a hazardous substance. IEC conditions can include drinking contaminated water (potable water), breathing contaminated indoor air (vapor intrusion), and contact
with contaminated soil (direct contact). An IEC is the highest priority case for the NJDEP due to the urgent need to protect public health,
safety, and the environment.
The IEC Guidance Document is available on the NJDEP's Site Remediation Program Webpage in the Guidance Library
(nj.gov/dep/srp/guidance/#iec). Additional information regarding an IEC can be obtained by contacting the NJDEP Office of Community Relations
(OCR) at (609) 292-2943 and the NJDEP Bureau of Environmental Measurements and Site Assessment (BEMSA) at (609) 376-9424.
Each IEC has an assigned NJDEP case manager who oversees response actions. These response actions are performed by a responsible party or the NJDEP. The NJDEP's IEC case
manager monitors the responsible party's receptor and source mitigation measures and ensures public health is protected. The NJDEP also addresses IEC conditions using public
funds to protect public health, safety, and the environment when the source of the contamination is unknown or the responsible party is unable or unwilling to
address the IEC.
How to Use This Information
The GIS map identifies IEC conditions at which the responsible party and/or the NJDEP has undertaken an IEC response action due to the urgent need to protect human health,
safety, and the environment
The map includes various shaped points representing the three broad types (vapor, potable well and direct contact) of active IECs as depicted and described below:
Vapor Intrusion IEC (diamond) - A vapor intrusion IEC exists when a discharge of a hazardous substance results in contamination above an indoor air
Rapid Action Level (RAL) in a building and there is a demonstrated pathway between the subsurface hazardous substance release and the RAL exceedance in a building,
(i.e., the contamination is entering the building from the ground and is not from materials stored or activities conducted inside the building).
Potable Well IEC (circle) - A potable well IEC exists when a discharge of a hazardous substance results in contamination above a Class II Ground Water
Remediation Standard in water being used for potable purposes.
Direct Contact IEC (square) - A direct contact IEC exists when a discharge of a hazardous substance results in the presence of contamination above acute
health effects levels in the upper six inches of the soil column and there is actual or potential for human contact via dermal contact, ingestion, or inhalation. An acute
health effect is when an adverse human health impact could result from an exposure of less than two weeks.
An IEC with a status of In Progress is one where a response action is currently underway to address the impacted receptor(s) and are colored blue for a potable
well IEC; purple for a vapor intrusion IEC and orange for a direct contact IEC. All green colored symbols represent an IEC where the receptor has been addressed and a receptor
control is in place which protects the public from being exposed to the contamination.
Reports Available in DataMiner
DEP Data Miner includes a variety of reports that provide the user with up-to-the-minute results from many
different environmental media and subjects. There are two reports that pertain directly to an IEC:
- Sites with an Immediate Environmental Concern
- Sites with an Immediate Environmental Concern by Municipality
Site Remediation NJ GeoWeb Profile
The Site Remediation NJ Geoweb Profile mapping application allows you to easily identify Known Contaminated Sites, Immediate Environmental Concerns and other highly
informative NJDEP Site Remediation data layers both within and proximate to your community. Upon launching this application, you will find links to a User's Guide and Tutorial
to help you to use the tools within the mapping application (outlined in red below). There is also a link (Layer List Groupings/Descriptions/Metadata) that will provide
detailed information concerning each of the GIS layers present within the application, including the IEC layer.
To view the IEC GIS layer, click on layer list at the top right of the screen (circled in red below), then click on Sites and Facilities (outlined in red below), find the IEC
layer in the list of GIS layers and click the check box in order to display it in the map. You can also click the small gray triangle to the left of the checkbox to display
the symbology for the IEC GIS layer:
You can find specific information about an IEC by clicking on the IEC symbol on the map and opening the pop-up for the IEC:
Additional information concerning the IEC Source, IEC Receptors and Licensed Site Remediation Professionals (LSRPs) associated with the IEC can be obtained by clicking on
any of the three Related Tables displayed at the bottom of the IEC pop-up window to view this information (in this instance Receptor related data are selected and displayed).